140g @ 10%, 170g @ 5%
PlasmaBlock® Air Cooled
Overview
A new design PlasmaBlock® featuring a one-piece block/heat sink that dissipates heat more efficiently and allows greater ozone generation related to it's overall size. The Gen1 enhanced block generates 170g per hour of 5% Wt. The Gen2 block generates 140g per hour of 10% Wt.
- Silent, Rugged, Reliable, Cost-effective
- Fully automatic tuning for constant ozone output and installation simplicity
- Service simplicity due to automatic fault diagnostics
- No exposed high-voltage safety hazards
- Now available with PlasmaVIEW® software (optional).
For additional application information, see the PlasmaBlock® Application Guide Manual.
-
Front Left
-
Front Right
-
Rear Left
-
Rear Right
-
Top Air Flow
-
Front Left Air Flow
-
Rear Left Air Flow
-
140g Gen2 20psi
-
170g Gen1E 10psi
-
Performance Graphs Legend
-
Front
-
Side
-
Top
-
Bottom
-
DAT210 Set Power Point
-
DAT210 Start Button Sweep
-
DAT210 New Profile Procedure
-
DAT210 Normal Running
-
DAT210 LED Fault Indicators
-
DAT210 Connection Safety Considerations
-
DAT210 On Delay Timer
-
Fuse and Power Supply Testing
-
IGBT and Diode Bridge Testing
-
16 Pin Kit Testing
-
DAT210 Firmware 3 1
-
SSD110 Tuning
-
Installation Operation
-
DAT210 Installation Operation
-
DAT210 Quick Start
-
Dimension Drawing
-
How to read the performance graphs
-
PlasmaBlock Performance Specs (heat dissipation, current, ozone output)
-
Spec Sheet
Product Details
- Wi-Fi and digital communications available as an option.
- Digital communications optional: simple and less expensive.
- Micro Processor based, installation simplicity and automatic tuning for constant ozone output.
- Automatic bus voltage compensation stabilizes output as power line conditions change.
- Pulse Density Modulation (PDM), linear power (ozone) output even at high turn-down.
- Service simplicity due to automatic fault diagnostics.
- Easy interface to PLC or computer.
- Efficient, compact, silent (25khz), safe, rugged, reliable, advanced – all the normal traits of a PTI product. Same precise linear control, with turn down to 1%, as with all Plasma Block® products.
- Maximum up-time , durable, commercial / industrial solution the ozone industry requires.
- Possible cell flooding is identified followed by shutdown and enunciation. No damage is caused to electronics, transformer and rarely the cell. Cell flushing and drying in the field is usually sufficient to restore full service.
- Control connections of the essential I/O functions are the same as all other Plasma Block® products.
- Line voltage 240v (UL approved) and 120v (not UL approved).
- Military grade conformal coating eliminates problems associated with condensation and mold, and greatly retards damage caused by accidental ozone exposure.
- There is an inherent pressure drop associated with each Plasma Block. This can vary depending on the desired flow. Verification of the outlet pressure, at the desired flow, of the Plasma Block is crucial in order to prevent a negative pressure drop in the Plasma Block. This will damage the Plasma Block internals and is not a warrantied repair.
Configuration options
PTI will set up and tune units to the customers desired specifications.
Oxygen pressure - (10 - 100 psi) (UL 5x rated)
Oxygen flow liters/minute - 5 - 60 slpm
Heat load btu/hr = 4400 btu
Chassis (stand alone)
Inlet fittings (none, 3/8", other)
Outlet fittings (none, 3/8", other)
Weight Lbs (Kg) :
complete package - 37.7 lbs (17.34 Kg)
modular - 32.9 lbs (15.1 Kg)
DAT210 is the standard control circuit board for this unit.